Difference between revisions of "HPL1/Content Creation"
m (Mudbill moved page Hpl1:Documentation:content creation document to HPL1/Content Creation without leaving a redirect) |
m (Fixed broken links) |
||
| Line 1: | Line 1: | ||
| − | = HPL-Engine© Content Creation = | + | =HPL-Engine© Content Creation= |
| − | == Table of Contents == | + | ==Table of Contents== |
| − | == 1. Introduction == | + | ==1. Introduction== |
| − | === 1.1 Some forewords === | + | ===1.1 Some forewords=== |
Welcome dear content creator to the HPL-Engine. | Welcome dear content creator to the HPL-Engine. | ||
| Line 14: | Line 14: | ||
Or something else depending on what the variables should describe. | Or something else depending on what the variables should describe. | ||
<br /><br /> | <br /><br /> | ||
| − | === 1.2 Setup === | + | ===1.2 Setup=== |
Below are just some general rules and settings. | Below are just some general rules and settings. | ||
| Line 21: | Line 21: | ||
'''National Settings'''<br />All the tools for the engine uses a dot “.” as a decimal separator. If you are Swedish or something this might not be how your computer is set up. Open the ''control panel->national settings'' and check so that this is correct! Also don’t forget to write decimals with dot and '''not comma.''' | '''National Settings'''<br />All the tools for the engine uses a dot “.” as a decimal separator. If you are Swedish or something this might not be how your computer is set up. Open the ''control panel->national settings'' and check so that this is correct! Also don’t forget to write decimals with dot and '''not comma.''' | ||
| − | {| class="wikitable sortable" border=1 | + | {| class="wikitable sortable" border="1" |
| − | | Good: | + | |Good:||1.00||1.23||234.3 |
|- | |- | ||
| − | | Bad: | + | |Bad:||1,000||1,23||234,3 |
|- | |- | ||
|} | |} | ||
| Line 30: | Line 30: | ||
| − | === 1.3 Exporter used === | + | ===1.3 Exporter used=== |
Collada is used to export models and maps. The exporter can be used for most major 3d packages, however HPL cannot load all of the files created from the different exporters. Currently Maya is the most supported package. | Collada is used to export models and maps. The exporter can be used for most major 3d packages, however HPL cannot load all of the files created from the different exporters. Currently Maya is the most supported package. | ||
More information is found at:<br />http://collada.org/public_forum/<br />Maya specific information is found at:<br />http://colladamaya.sourceforge.net/<br /> | More information is found at:<br />http://collada.org/public_forum/<br />Maya specific information is found at:<br />http://colladamaya.sourceforge.net/<br /> | ||
| − | Exporters known to work properly with current HPL release can be found in | + | Exporters known to work properly with current HPL release can be found in [[HPL1/Getting started]].<br /><br /><br /><br /> |
| − | == 2. Creating Models == | + | ==2. Creating Models== |
| − | [[ | + | [[HPL1/Content Creation Chapter 2|2. Creating Models]] |
| − | == 3. Creating maps == | + | ==3. Creating maps== |
| − | [[ | + | [[HPL1/Content Creation Chapter 3|3. Creating maps]] |
| − | == 4. Creating Materials == | + | ==4. Creating Materials== |
| − | [[ | + | [[HPL1/Content Creation Chapter 4|4. Creating Materials]] |
| − | == 5. HPL Helper == | + | ==5. HPL Helper== |
| − | [[ | + | [[HPL1/Content Creation Chapter 5|5. HPL Helper]] |
| − | == 6. Entity files == | + | ==6. Entity files== |
| − | [[ | + | [[HPL1/Content Creation Chapter 6|6. Entity files]] |
| − | == 7. Configuration files == | + | ==7. Configuration files== |
| − | [[ | + | [[HPL1/Content Creation Chapter 7|7. Configuration files]] |
| − | == 8. Naming and structure == | + | ==8. Naming and structure== |
| − | [[ | + | [[HPL1/Content Creation Chapter 8|8. Naming and structure]] |
Revision as of 20:10, 19 July 2020
Contents
HPL-Engine© Content Creation
Table of Contents
1. Introduction
1.1 Some forewords
Welcome dear content creator to the HPL-Engine.
In some parts of the doc naming conventions are described. This are described something like this:
_thing_[name]_[stuff]
This means that “[name]” and “[stuff]” are variables and are to be replaced with other text. The above example could be translated to:
_thing_thomas_lighter
Or something else depending on what the variables should describe.
1.2 Setup
Below are just some general rules and settings.
Units:
The game will use SI-units for measurements. This means that 1 length unit equals 1 meter, 1 time unit equals 1 second, 1 mass unit equals 1 kg and so on.
National Settings
All the tools for the engine uses a dot “.” as a decimal separator. If you are Swedish or something this might not be how your computer is set up. Open the control panel->national settings and check so that this is correct! Also don’t forget to write decimals with dot and not comma.
| Good: | 1.00 | 1.23 | 234.3 |
| Bad: | 1,000 | 1,23 | 234,3 |
1.3 Exporter used
Collada is used to export models and maps. The exporter can be used for most major 3d packages, however HPL cannot load all of the files created from the different exporters. Currently Maya is the most supported package.
More information is found at:
http://collada.org/public_forum/
Maya specific information is found at:
http://colladamaya.sourceforge.net/
Exporters known to work properly with current HPL release can be found in HPL1/Getting started.